Questions tagged [status-completed]
Indicates that the report has been resolved through the implementation of a feature or the fixing of a bug.
12
questions
5
votes
3
answers
241
views
Can we get mhchem support?
We got MathJax enabled. Today I learned that there is even more! We could have support for Physical units enabled as part of the mhchem package! We use physical units a lot and demand the SI ...
- 20.5k
10
votes
0
answers
164
views
We're graduating!
3DPrinting Stack Exchange is leaving Beta in mid-December.
What is Beta?
As the (somewhat out of date) Help Center article says:
“Beta” means that the site is still being defined and constructed.
We ...
0scarMod
- 33.2k
6
votes
3
answers
287
views
Does this 3D Printing site want only three votes to close (or should we stick with five)?
I've just noticed this Meta post, Testing three-vote close and reopen on 13 network sites and I wondered whether we should employ it here, and what do other people think?
We are a smallish site, with ...
GreenonlineMod
- 5,978
3
votes
3
answers
200
views
Which character to use to activate MathJax?
We were offered to get MathJax enabled.
Now, we need to decide on which character to have text between them parsed into MathJax! So please either add your suggestion or cast your vote!
- 20.5k
8
votes
2
answers
221
views
Can we get MathJax enabled?
Our site is dealing with electronics and practical engineering, so we use formulas in questions and answers on occasion, most usually when we have to figure out electronic ratings.
When we talk ...
0scarMod
- 33.2k
3
votes
1
answer
43
views
Tag required for "object removal from print bed"
With respect to this question, How can you both reliably print and remove your item without breaking it when detatching it?, the OP rightly states the following:
ps. I didn't find (and I can't make ...
GreenonlineMod
- 5,978
7
votes
4
answers
307
views
What does it take to get out of Beta stage?
I can't find an answer to this question on the "mother" meta website; hope this is not related to my choice of words in the search box.
The statistics of the 3D Printing on Area51 show that only few ...
0scarMod
- 33.2k
4
votes
2
answers
71
views
Should we turn on "inlined video"? [duplicate]
We have, now, assertained that inlined videos (for want of a better description) are currently turned off (disabled) for SE 3D Printing, but can be turned on at any time, and there is no need to wait ...
GreenonlineMod
- 5,978
2
votes
3
answers
98
views
Is the "inlining videos" capability turned off on this site? [duplicate]
I have just edited a new post, Help understanding bridge settings, so that the video would be "inlined" and playable in the post itself1.
However, the video does not show up, and only the ...
GreenonlineMod
- 5,978
2
votes
1
answer
35
views
Typo in arduino-mega-2560 tag
We have an arduino-mega-2560 tag but we also have an incorrectly spelled arduino-meda-2560 tag (which unfortunately is used far more often than the correct tag).
Creating a synonym doesn't seem the ...
- 14.6k
1
vote
1
answer
248
views
Do we want MathJax support on 3D Printing? [duplicate]
MathJax support allows questions and answers to contain pretty mathematical formulae, easy subscripts & superscripts, fractions, roots and greek letters etc. all using LaTeX syntax.
I have seen ...
- 215
5
votes
1
answer
41
views
Close votes review cue hangs - bug
When attempting to access the review cue for close votes,the cue hangs and errors out.
The error states - An error occurred when loading the review item, please try again.
I am able to open review ...
- 145